您的位置:网站首页 > 制钉机

全自动制钉机使用原理及方法

作者:管理员 来源:未知 日期:2011/9/27 16:19:58 人气: 标签:
导读:全自动制钉机使用原理:全自动制钉机配置有三台不同规格的拉丝机及一台抛光机。适用于Φ3-8mm的各类废钢筋、电焊条、车钢丝、铁丝等废旧原料。首先根据不同规格原…

全自动制钉机使用原理:
全自动制钉机配置有三台不同规格的拉丝机及一台抛光机。适用于Φ3-8mm的各类废钢筋、电焊条、车钢丝、铁丝等废旧原料。首先根据不同规格原料,分别选用不同规格的拉丝机进行拉丝和除锈(同时完成),然后送到制钉机,一次加工成圆钉:2寸、2.5寸、3寸、3.5寸等等(根据圆钉规格调整制钉和模具),再经过抛光机抛光便可打包出厂。
全自动制钉机使用方法:
全自动
制钉机制钉机、自动化程度高,操作十分简便,老人妇女、伤残人员均可操作。
在用
制钉机生产过程中,圆钉的钉帽和钉尖在一道工序中同时完成。在制钉机上更换不同的模具,就能生产出2-6寸各类规格的圆钉。以生产6寸钉为例:先将6.5钢筋经过6.5拉丝机拉丝,送到制钉机即一次打成6寸圆钉。以生产3寸钉为例:先Φ4mm将钢筋经过A拉丝机拉制Φ3.4mm,然后送到制钉机上,换上3寸钉的模具,即可打出(80×3.4mm)标准3寸钉;生产2.5寸钉,3.5钢筋,再经过B拉丝机拉至Φ2.8mm时送到制钉机上(换上2.5寸钉模具),开启电源,即一次打成2.5寸(6×2.8mm)圆钉。(图/文www.zhidingjixie.com

中译英
Automatic nail-making machine principle:

Automatic nail making machine is configured to have three different specifications of the wire drawing machine and a polishing machine. Applicable to all types of waste steel, than 3-8mm welding rod, wire, wire and other scrap materials car. According to the different specifications of raw materials, we choose different specifications of the wire drawing machine for drawing and rust ( completed ), and then sent to the nail making machine, a processing into a round nail: 2 inch, 2.5 inch, 3 inch, 3.5 inch, ( according to a round nail size adjusting nail and die ), and then after a polishing machine can packing factory.

Automatic nail making machine using the method:

Automatic nail mechanism for nailing machine, high degree of automation, the operation is very simple, elderly women, disabled persons can operate.

In the production process, round nails in the nail cap and the nail tip in a process at the same time. In nail-making machine changing different mold, can produce all kinds of specifications 2-6 inches round nail. In the production of 6 inch nails for example : 6.5 steel after 6.5 drawing machine drawing, to nail machine once hit into 6 inch nails. In the production of 3 inch nails for example: < 4mm first reinforced by A drawing machine drawing of diameter 3.4mm, and then sent to the nail making machine, put on 3 inch nails die, can play ( 80 * 3.4mm ) standard 3 inch nails; the production of 2.5 inch nails, 3.5 bars, after B drawing machine to a 2.8mm when send nail-making machine ( for 2.5 inch nails die ), turn on the power, i.e. a 2.5 inch ( 6 x 2.8mm ) round nail.

本文网址:
共有:条评论信息评论信息
发表评论
姓 名:
验证码: